User Tools

Site Tools


usersguide:manpagesforadmins

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

usersguide:manpagesforadmins [2014/11/12 08:24]
lionelsambuc created
usersguide:manpagesforadmins [2014/11/12 08:25] (current)
lionelsambuc
Line 1: Line 1:
 +====== MAN pages for administrators ======
 +
 +[[.:​manualpages|add_route(8)]] - configure IP routing \\
 +[[.:​manualpages|adduser(8)]] - add a new user to the system \\
 +[[.:​manualpages|backup(8)]] - backup files \\
 +[[.:​manualpages|badblocks(8)]] - put a list of bad blocks in a file \\
 +[[.:​manualpages|boot(8)]] - from power on to the login prompt \\
 +[[.:​manualpages|chown(8)]] - change owner \\
 +[[.:​manualpages|cleantmp(8)]] - clean out a tmp dir \\
 +[[.:​manualpages|config(8)]] - configuring MINIX 3 tasks and servers \\
 +[[.:​manualpages|cron(8)]] - clock daemon \\
 +[[.:​manualpages|dhcpd(8)]] - dynamic host configuration protocol daemon \\
 +[[.:​manualpages|fdisk(8)]] - partition a hard disk [IBM] \\
 +[[.:​manualpages|fingerd,​ in.fingerd (8)]] - remote user information server \\
 +[[.:​manualpages|ftpd,​ in.ftpd, setup.anonftp (8)]] - DARPA Internet File Transfer Protocol server \\
 +[[.:​manualpages|getty(8)]] - system login banner \\
 +[[.:​manualpages|halt(8)]] - abruptly stop the system \\
 +[[.:​manualpages|ifconfig(8)]] - configure a TCP/IP device \\
 +[[.:​manualpages|inet,​ inet.conf (8)]] - TCP/IP server \\
 +[[.:​manualpages|init(8)]] - grandparent of all processes \\
 +[[.:​manualpages|installboot(8)]] - make a device bootable \\
 +[[.:​manualpages|intr(8)]] - run a command with interrupts enabled \\
 +[[.:​manualpages|irdpd(8)]] - internet router discovery protocol daemon \\
 +[[.:​manualpages|mknod(8)]] - create a special file \\
 +[[.:​manualpages|nonamed(8)]] - not a name daemon, but acts like one \\
 +[[.:​manualpages|part(8)]] - partition table editor \\
 +[[.:​manualpages|partition(8)]] - make a partition table \\
 +[[.:​manualpages|pr_routes(8)]] - show IP routing \\
 +[[.:​manualpages|printroot(8)]] - print the name of the root device on standard output \\
 +[[.:​manualpages|pwdauth(8)]] - password authentication program \\
 +[[.:​manualpages|rarpd(8)]] - reverse address resolution protocol daemon \\
 +[[.:​manualpages|rdate(8)]] - set time and date from a remote host \\
 +[[.:​manualpages|readclock(8)]] - read the AT's real time clock \\
 +[[.:​manualpages|reboot(8)]] - reboot the system immediately \\
 +[[.:​manualpages|repartition(8)]] - load a partition table \\
 +[[.:​manualpages|rlogind,​ in.rlogind (8)]] - remote login server \\
 +[[.:​manualpages|rshd(8)]] - remote shell server \\
 +[[.:​manualpages|screendump(8)]] - write current console screen to standard output \\
 +[[.:​manualpages|serial-ip(8)]] - Serial IP (SLIP or PPP) setup \\
 +[[.:​manualpages|service(8)]] - Start or stop an operating system server or device driver \\
 +[[.:​manualpages|setup(8)]] - Install MINIX 3 on a hard disk \\
 +[[.:​manualpages|shutdown(8)]] - graciously close the system down \\
 +[[.:​manualpages|slip(8)]] - Serial Line IP \\
 +[[.:​manualpages|srccrc(8)]] - compute CRC checksums of the entire source tree \\
 +[[.:​manualpages|sync(8)]] - flush the cache to disk \\
 +[[.:​manualpages|update(8)]] - periodically write the buffer cache to disk \\
 +[[.:​manualpages|usage(8)]] - installing and using MINIX (//Needs updating//​)\\
  
usersguide/manpagesforadmins.txt · Last modified: 2014/11/12 08:25 by lionelsambuc